sproutbean1

Fiat 500 Replacement Key Fob If your remote key fob isn't functioning, it could be time to replace the battery. If you replace the battery, but it isn't working the issue could be elsewhere. United Locksmith specializes in the creation of new keys for classic vehicles. We have the tools and components needed for this service. Dead Coin Battery A dead battery is the primary cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob is equipped with a coin cell battery which will quickly drain if it is not utilized frequently enough. If your remote has started to show signs like a loss of range or stopped working, then the battery may be dead. Metal clips keep the battery securely in the key fob. If the clips aren't tight, they can cause contact issues that prevent your remote from receiving power. Using a small flathead screwdriver, push the clip that holds the retaining pin open to remove the current battery and insert a new one. Make sure to use a battery with the same voltage, size, and specification as the original. fiat doblo key programming can also be damaged or corroded by water exposure. Even a quick bath in soapy, warm water could damage the chip. Keep your key fob dry. Water Damage Water damage could be the reason for your key fob not working properly. Key fobs have rubber seals that stop them from being damaged by rain or a splash of water. However, it is crucial to keep your car keys out of the ocean, pool, and washing machine! The key fob comes with an electronic chip that sends an electronic message to the immobilizer system in your car. This is what allows your 500 to start or lock, however in the event that the chip becomes wet, it's unable to longer function. You can try cleaning the internal electronics of your key fob using isopropyl alcohol, or an electronic cleaner to see whether they're still working. However, it's better to purchase a new one from a dealership instead of trying to repair a key fob that was submerged in salt water. Although a replacement fob may cost a bit of money, it's a lot cheaper than having to pay for your Fiat 500 to be towed to the dealer and repaired! You can also do it yourself with just a few steps. Be sure to have the correct battery type before attempting to open your keyfob. This is a job that's far simpler than it appears, and there are step-by-step instructions online for nearly every car key fob. Faulty Chip The chip in the key fob communicates with the immobiliser in your car to ensure that your vehicle will only start when right keys are in place. If the chip is damaged, or corrupted it won't allow your car to start, no matter what you do. Damage to the water or a dead phone battery are the most frequently cited reasons for the chip being damaged. Regardless of the reason, it is an ideal idea to hand the work to a locksmith, as they will be able to replace the chip fast and at a cost-effective price. If your key fob stops working after exposure to clean water from the tap or rain, take out the battery and clean the electronic component using a paper towel to ensure it's dry before putting it back into. If the key fob doesn't work it's likely to be a fried chip and is required to be replaced. A few people turn to their dealer when in need of an entirely new Fiat key fob, however it can be a costly option. United Locksmith is the best option if you want your Fiat key fob repaired at a reasonable cost. We have the tools and knowledge necessary to fix your Fiat key fob in a timely and professional manner. Faulty Receiver Module Fiat key fobs send signals of up 50 feet to the vehicle, which can unlock and close the doors (and start the vehicle for those with automatic transmissions). However there are a few factors that could cause the fob to stop working. It could be due to a dead battery damaged by water or worn buttons as well as a receiver module problem and signal interference, or an electronic chip that is malfunctioning. If the fob was located in a pocket which has suffered severe trauma (such as being dropped onto the floor or washed in the washing machine) the fob might not be in a position to connect with the Body Control Module (BCM) of the car. The BCM is a security system which will only accept signals from genuine original keys. You'll need to replace the fob if this occurs. A professional locksmith will handle the entire replacement process including programming a new key to your 500. They can even provide you with an clone fob that performs the same as the original (and costs only one-third of what it would cost).